High quality pressure sensors for industrial applications. Pressure sensors with stainless steel sensor or ceramic senso Check Out Pressure on eBay. Fill Your Cart With Color today! Over 80% New & Buy It Now; This is the New eBay. Find Pressure now

Convert a pressure reading of 2.1 Torr into mbar units. Start on the left side of the table and move down vertically until you reach the row labeled Torr. Move horizontally to the right along that row until you reach the 'Torr-to-mbar' conversion factor at the intersection with the mbar column. The conversion factor is 1.3332 (mbar/Torr) Pressure Conversion Factors Table. This table shows the factors for doing various pressure conversions. Many are uncommon but have specific uses for certain situations. Convert From Convert To Multiply By; atmosphere, standard (atm) pascal (Pa) 1.01325 E+05: atmosphere, standard (atm

- To convert among any units in the left column, say from A to B, you can multiply by the factor for A to convert A into Pascals then divide by the factor for B to convert out of Pascals. Or, you can find the single factor you need by dividing the A factor by the B factor
- A kilopascal is equal to 1000 pascals. Another commonly used unit of
**pressure**is the atmosphere (atm). Standard atmospheric**pressure**is called 1 atm of**pressure**and is equal to 760 mmHg and 101.3 kPa. Atmospheric**pressure**is also often stated as pounds/square inch (psi) - Pressure Conversion table and factors: atmosphere. Quantity : Reference Unit : is equal to : Conversion Factor : Unit :
- Pressure - Conversion Pressure (the symbol: p) is the ratio of force to the area over which that force is distributed, and it is the amount of force acting per unit area. The SI unit of pressure is the pascal, symbol Pa. A pressure of 1 Pa is small, which approximately equals the pressure exerted by a dollar bill resting flat on a table
- Pressure Conversion . Convert what quantity? From: To: Result: Information: -force is added to distinguish units of force from units of mass. The common PSI stands for pounds per square inch or pounds/square inch. BookMark Us. It may come in handy..

- Pressure Sensors Conversion Factors Honeywell1Sensing and Control11-800-537-6945 USA1F1-815-235-6847 International11-800-737-3360 Canada125 REFERENCE AND APPLICATION DATA CONVERSION FACTORS Converting To PSI 1in. H 2O (@ 0°C) J 3.6127 · 10-2 psi 1in. H 2O (@ 20°C) J 3.6063 · 10-2 psi 1mm H 2O (@ 0°C) J 1.4223 · 10-3 psi 1mm H 2O (@ 20°C.
- Pressure Unit Conversion Table atm ata ( kg/cm2 ) Torr ( mm Hg) in Hg (32℉) mm water (4℃) in (60℉) bar Mpa Kpa PSI ( lb/in) atm 1 1.033 760 29.92 10332.56 406.79 1.013 0.1013 101.32 14.69 ata ( kg/cm2 ) 0.968 1 735.56 28.96 10000.03 393.71 0.981 0.0981 98.07 14.2
- The.25636 factor used in the formulas and in the calculation of the table conversion factors is the vapor pressure of water at 60 degrees Fahrenheit as published in GPA Standard 2172-96
- ator. The conversion examples above are examples of a one being involved. For example, 760.0 mmHg / 1 atm in examples 1 and 2. The 1 was assumed to be present
- Pressure Conversion Factors: Pressure Swipe to the right for more table information LB in. 2 IN. Hg at 0C IN. H 2 0 at 4C FT
- Multiply the flowrate indicated on the meter by the correction factor. This will equal an approximation of the flowrate of the gas being used. Please note: this correction factor is only accurate within ±10%. This is also inaccurate for extremely low flow, or elevated pressure; consult factory for your specific condition
- pressure conversion factors provided by unitconversion.org: Time Master II - Time Calculator for Pilots, Accounting, Broadcasting; Ultra Measure Master - Most Complete, Easy-to-Use Metric Conversion Calculator; Measure Master Pro - Feet-Inch-Fraction Calculator for Do-It-Yourselfers.

Corresponding pressure units: Notes The table refers to ISO 31-1:1992 and ISO 31-3:1992 For lengths ISO 31-1 defines conversion factors for units no longer to be used: inch (in) foot (ft) For pressures ISO 31-3 defines conversion factors for units no longer to be used: pound-force per square inch (lbf/in.²) conventional millimetre of water (mmH2O Covers gas pressure units and conversion of pressure units ** A table of conversion factors between common length units is provided below: in ft yd mi NM m mm km; 1 in (inch) = 1: 0**.08333333: 0.02777778: 1.578283 E-5: 1.371490 E-5: 0.0254: Fluid Pressure. A table of conversion factors between common fluid pressure units is provided below: psi psf kPa atm bar in Hg mm Hg in H 2 O mm H 2 O; 1 psi (lbf. Pressure [P] and Volume [V] are inversely proportional. That is when pressure is doubled the volume is halved. Simple Pressure Factor Using the basic principle of Boyles Law we can easily calculate a simple pressure factor (Fp) to be used for calculating changes in volume caused by increases or decreases in pressure

Conversion Factors. Conversion Factors Length. 1 kilometer (km) = 1000 meters (m) 1 meter (m) = 100 centimeter (cm) 1 centimeter (cm) = 10-2 m. Pressure. 1 nt/m 2 = 10 dynes/cm 2 = 9.869 × 10-6 atmosphere = 2.089 × 10-2 lbwt/ft 2. 1 lbwt/in 2 = 6895 nt/m 2 = 5.171 cm mercury = 27.68 in water. 1 atmosphere. Thus to express, for example, the pressure p = 11.8 standard atmospheres (atm) in pascals (Pa), write p = 11.8 atm × 101 325 Pa/atm and obtain the converted numerical value 11.8 × 101 325 = 1 195 635 and the converted value p = 1.20 MPa Metric Conversion > Pressure conversion. Pressure conversion. Use the search box to find your required metric converter → iPhone & Android app Pressure Pascals Bar Pound force per square inch Atmospheres More units.. Temperature Weight Length Area Volume Speed Time Angle Energy and Power Health and Wellbeing Metric Conversion Table Pressure P is defined as P = F A P = F A where F is a force applied to an area A that is perpendicular to the force Conversion Guide. Convert pressure units with the pressure unit converting tool, look up a conversion from the tables, identify a pressure unit and its group association with other pressure units, or find the relevant pressure conversion factor in pascals. Conversion Tables. Choose a look up table for a specific pressure conversion application

Free online pressure conversion calculator - converting between 52 pressure units,including pascal (Pa),kilopascal (kPa),bar,psi (psi),ksi (ksi Pressure Measurement in Process Systems Differential pressure is the pressure measurement most frequently encountered in industrial process systems. Differential pressure is the difference in pressure between two points in a system. Differential pressure gauges will have two inlet ports, each connected to one of the two points being compared Chemistry 301. Units . 0. Fundamentals; 1. Gases; 2. Atomic; 3. IMFs; 4. Thermo; FAQs; Links. Learning Strategie

feet of gas which has an energy value factor of 1.050. Btu Energy value = (1,000 cf) (1.050) = 1,050 Pressure Base Correction - The measured pressure base may be different from the contract pressure base. Due to the different pressure bases used for reporting volume and heating value, it is usually necessary to put these number Two Conversion Factors. To enable our customers to compare gas prices from one region to another, we use a standard gas measurement unit, the Therm. Initially, a conversion factor must be used to convert CCFs to the standard atmospheric pressure, which is sea level pressure

pressure (psi) conversion factors. Principle of Reciprocity. pressure: Atmospheric Pressure at Altitudes Above Sea Level. pressure: Internal Fluid Pressure (psi) on Tubing. product-to-sum formulas. proximity sensor - inductive. PTC CREO Parametric Notes. pump system: Hand Pump System. PWM (pulse width modulation) Pythagoras' Theorem. Conversion factor chart shows a variety of units of measure for pressure encountered when working with cryogenic, vacuum, and pressure technologies. How to convert pressure units including mBar, Pa, mmHg, Torr, inHg, psi, atm, Bar and dyne * Title: Pressure Conversion Factors Description: Conversions for PSI, FT Water, Kg/Cm2, Atmosphere, Bar, Inch Mercury, and kPa*. Published: 10/5/2009 Last Edited: 9/18/2013 1 user found this article useful Pressure Unit Conversion by Tim Brice and Todd Hall. Enter an atmospheric pressure that you would like: Answers: inches of mercury: inches of mercury: millimeters of mercury (torr) millimeters of mercury (torr) millibars: millibars: hecto Pascals: hecto Pascals: kilo Pascals: kilo Pascals

The most frequently used units of pressure are pascal (Pa), kilopascal (kPa), megapascal (MPa), psi (pound per square inch), torr (mmHg), atm (atmospheric pressure) and bar. Atm (Atmospheric Pressure) Conversion: An atmosphere (atm) equals to the air pressure at the sea level at a temperature of 15 Celsius. 1 atm = 1.01325 bar → atm to ba ** 2 minute review over Pressure Conversion Factors**.** 2 minute review over Pressure Conversion Factors**

- - Pressure - Velocity - Volume - Volumetric Rate To convert a number from one unit to another: 1. Locate the unit in which the number is currently expressed in the left-hand column of the table; 2. Find the desired unit in the center column; and 3. Multiply the number by the corresponding conversion factor in the right-hand column. 9/85.
- Pressure - depth (EB 602#1) in ppg MWE using the standard conversion factor. Furthermore, the plot shows the same PPG MWE values at the base of the pay zone and the lower wet zone. On the contrary the P-D shows a weak regression between the middle and lower compartments, either due to the presence of the water leg or seal failure
- Conversion Factors Volume of Compressed Gas in a Cylinder To find the volume of gas available from a compressed gas cylinder, we apply the Ideal Gas Law (PV = nRT). In a high-pressure cylinder, the volume will be affected by the content's compressibility factor Z (PV = ZnRT). For example, an AL cylinder of pure helium may contai
- dimensions, the size and location of openings in the building, Importance and Safety factors, etc. It is important to note that this process is application specific - the required design pressure is not merely a conversion of wind speed using the previously indicated equations - it is dependent on many other factors. Wind Speed Conversion (MPH
- The cgs base pressure unit is barye (Ba), which equals to 1 dyne per square centimeter. Dyne is the force needed to accelerate mass of one gram to rate of one centimeter per second per second. As pressure unit conversion, 1 barye (Ba) equals 0.1 Pascal (Pa)

rotameter pressure correction factors pressure (psig) for which rotameter is pressure (psig) for which correction is to be made calibrated 02468. Conversion Factors Product Information Technical and Safety Information Safety Data Sheets Glossary Frequently Asked Questions Use our reference tools to accurately convert specifications for specialty gases and industrial gases, and associated gas handling equipment from Air Liquide All Pressure conversion table and factors: Metric Pressure conversion table and factors: List of abbreviations: Unit of measurement : Abbreviation : atmosphere atm attopascal aPa centimeter mercury (0°C) cmHg centimeter water (4°C) cmH2O centipascal cPa decipascal dPa dekapascal. A conversion factor is the number or formula you need to convert a measurement in one set of units to the same measurement in another set of units. The number is usually given as a numerical ratio or fraction that can be used as a multiplication factor. For example, say you have a length that is measured in feet and you wish to report on it in meters

Conversion tables •General conversion factors •Length •Pressure •Temperature. Properties of materials •Metals •Polymers. Miscellaneous •Glossary •Safety •Standard threads •Trademarks •Volume - frits •Volume - tubing •Warrant 1 psi (lb/in 2) = 6,894.8 Pa (N/m 2) = 6.895x10-3 N/mm 2 = 6.895x10-2 bar; Download and print Vacuum Units Converter Chart. Convert from % Vacuum to Unit of Pressure. The % of vacuum is a relative value where pressure at normal or standard atmosphere is the base value.. p v% = 100% - (p v / p atm) 100% (1). wher Download Pressure Unit Converter our powerful software utility that helps you make easy conversion between more than 2,100 various units of measure in more than 70 categories. Discover a universal assistant for all of your unit conversion needs - download the free demo version right away About Pressure Unit Conversion tool. We use rounding at unit-conversion.info. This means that some results will be rounded to avoid the numbers getting too long. While often rounding works up to a specific decimal place, we've decided that limiting the length of the result to 13 digits would be more favorable to keep the results consistent.

Pressure Units and Conversion Factors. Pressure is force per unit area. Pressure may be expressed in many different units. Units like pounds per square inch give the units used for force and area. Units that include length, like millimeters of mercury refer to the pressure exerted by a column of the liquid of that height. The unit atmosphere refers to the pressure exerted by the gases in our. Let's take a closer look at the conversion formula so that you can do these conversions yourself with a calculator or with an old-fashioned pencil and paper. The formula to convert from mmHg to atm is: atm = mmHg ÷ 76 NOTES: * There is no direct conversion between densities and pressure gradients. The relationship P = pgh has been used to obtain multiplication factors indicated by ''. The SI units of pressure gradient are kPa/m The SI units of density are kg/m Head/Pressure Conversion. Summary; Convert Head to Pressure; Convert Pressure to Head; Table of Pressure Conversions for Water; Summary. Pressure can be measured either as part of a scale (e.g. bar, pascals, psi) or in terms of the height of a fluid (e.g. metres of water)

- Windspeed
**conversion****factors**Meteorological data includes windspeeds which may be expressed as statute miles per hour, knots, or meters per second. Here are the**conversion****factors**for those various expressions of windspeed: 1 m/s = 2.237 statute mile/h = 1.944 knot - Conversion Factors — Pressure Units 1-708-425-9080 sales@mtm-inc.com When working with cryogenic, vacuum, and pressure technologies, you may encounter a variety of units of measure for pressure. The conversion factor chart below covers the range of pressure units you may encounter
- Pressure Conversion From the user, a value for atmospheric pressure (P)is given to be converted to different pressure units. To convert between inches of mercury (inHg)and millimeters of mercury (mmHg)or torr, use the formulas below: PmmHg = 25.4 × PinHg PinHg = 0.03937008 × PmmH
- The conversion factor is 0.052. Pressure Gradient psi/ft = Fluid Density in ppg X 0.052 Hydrostatic Pressure psi = Density in ppg X 0.052 X True Vert. Depth The Conversion factor 0.052 psi/ft per lb/gal is derived as follows: A cubic foot contains 7.48 US gallons
- A kilopascal is a unit of Pressure in the International System of Units (SI). The symbol for kilopascal is kPa. There are 6.89475729 kilopascals in a psi. Let's take a closer look at the conversion formula so that you can do these conversions yourself with a calculator or with an old-fashioned pencil and paper
- The pressure (P -psi) in the wellbore or formation can be expressed in terms of equivalent mud weight (EMW) and is given as. EMW = Pressure/ (0.052 x Length (true vertical depth, ft) Other References. More details can be obtained from 501 Solved Problems for Drilling Operations. Glossary of Drilling Operations. Conversion Factors. General.

PRESSURE FROM TO MULTIPLY BY psi millibar 68.95 psi Atm 0.068 Psi Inches H 20 27.68 kPa millibar 10 Inches H 20 millibar 2.40 VOLUME AND MASS TO MULTIPLY BY Litres 3.79 Imp galls Litres 4.55 SCH Litres 28.32 Pound kg 0.454 Imp Pint Litres 0.568 STANDARD GAS CONVERSIONS GAS RELATIVE DENSITY CONVERSION FACTOR* Acetylene 0.90 0.9 In this video I will explain the idea of pressure. I will also talk about pressure units and how to convert between the different pressure units using sever.. COMPRESSED AIR CONVERSION FACTORS 28.32 1.34 BY 14.7 0.06895 6.895 cu ft/min kW 14.23 cu ft/min horsepower bar psi psi kg/cm² bar kPa(kilopascal) psi VOLUME TO OBTAIN l/min bar kPa MULTIPLY psi PRESSURE 1: Browse through the page and find the unit you want to convert from. Type the value you are converting next to the unit. 2: Click the Convert button. Your value gets instantly converted to all other units on the page NIST Guide to the SI, Appendix B: Conversion Factors Expand or Collapse. NIST Guide to the SI, Appendix B.8: Factors for Units Listed Alphabetically; NIST Guide to the SI, Appendix B.9: Factors for units listed by kind of quantity or field of science; NIST Guide to the SI, Appendix C: Comments on the References of Appendix D - Bibliograph

- pressure in atm = 600 / 1.01325 x 10 5 atm (the Pa unit cancels out) pressure on Mars = 0.00592 atm or 5.92 x 10 -2 atm In addition to learning the conversion, it's worth noting the low atmospheric pressure means humans couldn't breathe on Mars even if the air had the same chemical composition as air on Earth
- These conversion tables are provided for your reference. Table 10 High Pressure Units Table 11 Low Pressure Units Table 12 Speed Units Table 13 Torque Units Table 14 Dynamic Viscosity Units Table 15 Kinematic Viscosity Units Table 16 Temperature Conversion Formulas Prefix Symbol Multiplying Factor exa E 1018 1 000 000 000 000 000 000.
- WASTEWATER TREATMENT CONVERSION FACTORS AND FORMULAS CONVERSION TABLE BASIC FORMULAS BASIC FORMULAS (SLUDGE & SOLIDS) =Pounds of BOD or TSS Flow, MGD x Concentration, mg/l x 8.34 Suspended Solids, mg/l (W2) -(W1) x 1000 x 1000 AREA TEMPERATURE ml Sample 1 Acre = BOD, mg/l43,560 Sq Ft °F = (°C x 1.8) + 32 = (Initial DO-Final DO) x BOD Bottle Vol, m
- If the Cv factor is the same for both paths, there will be about the same pressure loss through each. If the Cv factors are different, there will be a higher loss through the path with lower Cv factor. The chart shows the relation between inlet pressure, outlet pressure and flow capacity for any orifice or valve passage which has a Cv factor of.
- Use the conversion factors below to convert from inH2O to other pressure units or vice versa. To convert a reading in inH2O to another unit multiply it by the relevant pressure conversion factor. To convert a reading in any pressure unit to inH2O divide it by the relevant pressure conversion factor
- This converts common units of density both English Units and Metric. Simply put in the desired figure into the input box and select units kilograms per meter (cubed) , grains per gallon, grams per cubic centimeter, grams per liter, kilograms per liter, ounces per cubic inch, ounces per gallon, ounces per inch (cubed) tons per cubic meter and other units of density

Conversion Factors,All capacities and measurements in the catalog are expressed in uniform values. The conversion chart provides helpful information for their translation into equivalent systems Then select a pump from the preceding pages that will deliver 56.5 GPM at the desired pressure. Conversion Factors Multiply By To Obtain ; LENGTH: inches inches feet miles: 25.40 2.540 0.3048 1.609: millimeters (mm) centimeters (cm) meters (m) kilometers (km) AREA

2 Conversion Factors = 3.6 MJ* 1,500 3 Propane, butane and ethane converted API Gravity Correction Factor (CF) 0-6 0.9997 7-35 0.9996 36-51 0.9995 52-64 0.999 AEMO PRESSURE CORRECTION FACTORS 28/08/2015 239500-1 PAGE 3 . NOMINAL PRESSURE AT METER (IN KPA GAUGE) CORRECTION FACTOR . 300 3.9873 350 4.4890 400 4.9922 450 5.4961 The Pressure Correction Factors are used to convert the gas volumes as measured by basic meters to the standard volume which is then multiplied by the average heating value for th * Pressure Conversion Chart Convert equivalent pressure measurements across many different units of measure such as pascals to torr*, or atmospheres to bar with this pressure conversion table Pressure is the continuous exertion of physical force by something in direct contact with it A conversion factor is a ratio expressed as a fraction that equals 1. When we use conversion factors to convert units, we multiply our original measurement by the conversion factor to get the same.

Factors Affecting Equilibria. According to the Le Chatelier's Principle, states that if a system under equilibrium is subjected to a change in pressure, temperature or concentration, in this case, the equilibrium shifts further reducing as well as to counteract the effect of the change N = Unit conversion factor C = Discharge coefficient (accounts for energy losses, Reynolds number corrections, pressure tap locations, etc.) Y = Gas expansion factor A1 = Cross-sectional area of mouth A2 = Cross-sectional area of throat Zs = Compressibility factor of gas under standard condition

To Obtain micron (μm Hg) mm of Hg at 0 ° C (torr) atm psi bar kg/cm 2 kPa ft of H 2 O at 60 ° F in of H 2 O at 60 ° F in of Hg at 0 ° C; Multiply By; micron (μm Hg)--10x10-3: 1.31579x10-6: 1.9337x10-5: 1.33x10-6: 1.30x10-6: 1.33x10-4: 4.4603x10 6: 5.33524x10-4: 3.937x10-5: mm of Hg at 0 ° C (torr): 1.00 The above table is divided into units and values; the values are conversion factors. The first row and the first column represent the units and the remaining cells are the values. A unit in the first column has a unit value (e.g., 1 Pa, 1 bar) while a unit in the first row have a value of its conversion factor. Consider an example of Torr to Pa

Pressure Units and Conversion Factors Pressure is force per unit area. Pressure may be expressed in many different units. Units like pounds per square inch give the units used for force and area. Units that include length, like millimeters of mercury refer to the pressure exerted by a column of the liquid of that height. The unit atmosphere refers to the pressure exerted by the gases in our. Conversion factors for common engineering systems, particularly relating to pressure and vacuum systems ››Measurement unit: psig. Full name: pound/square inch [gauge] Plural form: pounds/square inch Symbol: lb/in 2 Alternate spelling: psig Category type: pressure Scale factor: 6894.75728 ›› SI unit: pascal The SI derived unit for pressure is the pascal The unit bar for pressure is clearly a metric unit, but its order of magnitude is a bit strange. In the centimeter-gram-second system of units we have: 1 bar = 1 000 000 baryes = 1 000 000 dyn/cm² so the bar is not coherent with this system (the factor is not one)